JIS K 2. RRP: Your Price: $1, SKU: JIS K 2. Vendor: Condition : Weight: LBS. Availability: Shipping: Calculated at checkout. Minimum. Find the most up-to-date version of JSA – JIS K at Engineering MS ISO BS ISO ASTM D JIS K (Clause 6). DIN AS MS ISO 3) Air Permeability.
|Published (Last):||19 April 2017|
|PDF File Size:||8.22 Mb|
|ePub File Size:||18.32 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, it was used for 50 jis k 6301 as rubber hardness measurement and is still used as test data agreed between concerned persons even now when it is progressed to shift to new JIS 6310 jis k 6301 standard is discontinued. In case there unevenness on the measured face, less flat face because of irregular shape and deep bump at the bottom, depressed face of durometer is difficult to reach and sometimes accurate measurement is not possible.
Our product line consists of various types of durometers applicable to specific materials as indicated in the chart above.
jis k 6301 The Pressure foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough to ensure accurate measurement. High accuracy and repeatability of the hardness readings are assured by the flexible joint function. However, it is used even now for measurement data or internal management data upon the agreement of concerned parties jis k 6301 to its iis use for many years within the rubber industry.
Pressure foot The Jiis foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough to ensure accurate measurement. It consists of 3 types of durometer jis k 6301 as Type A for medium stiffness, Type Jis k 6301 for high hardness and Type D for low hardness.
Constant Loader for Durometer Constant loarder assures uniform test pressure eliminating false readings due to differences between operators in measuring by hand.
Please select according to usage in addition to type A and Type D. Inspection is conducted at 2, 50, and points respectively.
JIS K-6301 1
But we distinguish model code as another durometer from conformity of standard point of view. Type A which is main type tends to indicate higher figure by 1 or 2 points jis k 6301 with conventional 63011 hardness measurement.
JIS K which had been established in and sustaining the base of rubber industry jis k 6301 Japan was discontinued in after the suspended period, as it was not in conformity with ISO, and Jis k 6301 6031 was newly established. Two-pointer type max-hand and active hand of Rubber Hardness Tester The stationary set hand max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen.
ASKER Durometer Type JC | Product | KOBUNSHI KEIKI CO.,LTD.
However, verification is recommended because a significant difference is estimated to be the largest when a durometer jis k 6301 measurement values from 10 to 90 points.
The most important consideration in using durometers is to select the correct type for purposes of measurement according to the specimen.
As is half ball type osibari this is suitable for soft material like soft rubber expanded rubberhardness of spool of textile jis k 6301 film roll to which osibari sticks if it is type A durometer.
Indentor Extension Tester The gauge to check the indentor height on a durometer and the reading indicator o. Type E 2 durometer with around jie of sponge spring load figure of type E, and type FO to measure hardness of polystyrene sponge for the level of sponge washing dishes are available.
GS 4kg weight option ZY The stationary set hand max-hand makes jis k 6301 maximum value easier to read and allows the creep characteristics of a specimen.
Load Tester jis k 6301 Hardness Tester Tester to check load properties of the spring on a durometer Jis k 6301 is conducted at 25, 50, and kis points respectively. Measurement example Hardness is being measured by placing GS G on the sponge sheet. There are 2 kinds of A type for general rubber and C type for hard rubber.
This standard is ruled jis k 6301 plastic business field in Japan apart from testing method of hardness of rubber. This is basically equal to JIS K of durometeras only its round up method of spring load figure etc. Night jis k 6301 and highest and lowest limiter equipped for the both are standard. To top of product information. Dispersion of polystyrene level can be judged. Type D is suitable for hard rubber of which measured figure by Type A 90 and above and Type E is suitable for soft rubber of which measured figure is below At that time, deep hole Jis k 6301 and long leg type L make measurement possible by making pressed face small or long.
Hardness Tester Selection Chart Our product line consists of various types of durometers applicable to specific materials as indicated in the chart above. Then, long leg type complies with DIN